Fsbuild-2 Flight Planner

I have the Coolsky MD81 (Super 80).
I set up the Aircraft.cfg with my weights.

I used the FSBuild MD80.prf on a flight:
LEMD PINA2N BRITO PONEN SEROX VILAR KARES BISES BCN TOLS1P LEPA
400nm

and the NavLog REQD fuel was 807 lbs.

Not enough fuel for the trip.

Is there something I have wrong or is the MD80.pfr wrong?


****
[md81] --- VBM I AM TESTING THIS
WeightUnit=LBS
PayloadWeight=18920
ReserveFuel=
AlternateFuel=
HoldFuel=:10
ExtraFuel=500
TaxiFuel=200
ApproachFuel=
DefaultTOFlaps=11
DefaultLDGFlaps=40
PerformanceData=MD80.prf
MaxTakeoffWeight=140000
MaxLandingWeight=130000
MaxCruise=35000
OperEmptyWeight=79686
CruiseAltitude=27000
ClimbSpeed=280
CruiseSpeed=340
DescentSpeed=280
MaxZeroFuelWeight=122000


*****
Fsbuild Flight Plan
FLT REL IFR LEMD-04/LEPA-24L MACH A/C md81
FUEL TIME CORR TOGWT LDGWT AVG W/C
TAXI 000200 0010 . . . . 099213 099152 P000
DEST LEPA 000060 0104 . . . . ELEV. 27 FT
RESV 000025 0030 . . . .
ALTN 000013 0015 . . . . ALTN LEIB DIST 75
HOLD 000008 0010 . . . .
EXTRA 000500 1000 . . . . ZFW 098606 PAYLOAD 018920
TTL AT TO 000607 1159 . . . . DIST 0398
REQD 000807 1209 . . . . ETD

CLB BIAS 0.0% CRZ BIAS 0.0% DSC BIAS 0.0%
DEP BIAS 0 min 0 dist 0 fuel, ARR BIAS 0 min 0 fuel

LEMD PINA2N BRITO PONEN SEROX VILAR KARES BISES BCN TOLS1P LEPA/0104

M/H FL WIND ATC
TO NM AWY M/C TAS G/S ZT ACTME STA/CODE ACBO ABO REM AREM

N4058.8/W0235.9 055 CLB 000000 LECM
PINAR 053 DCT 055 279 279 00/13 00/13 / 0000/... 0005/...

N4104.7/W0204.6 076 270 000000 LECM
BRITO 024 DCT 076 425 425 00/03 00/16 / 0000/... 0005/...

N4121.2/W0032.8 077 270 000000 LECM
PONEN 071 DCT 077 425 425 00/10 00/26 / 0000/... 0005/...

N4120.8/E0013.1 090 270 000000 LECB
SEROX 035 DCT 090 425 425 00/04 00/31 / 0000/... 0005/...

N4120.5/E0033.9 090 270 000000 LECB
VILAR 016 DCT 090 425 425 00/02 00/33 / 0000/... 0005/...

N4119.8/E0109.1 091 270 000000 LECB
KARES 026 DCT 091 425 425 00/03 00/37 / 0000/... 0005/...

N4119.1/E0141.3 091 270 000000 LECB
BISES 024 DCT 091 425 425 00/03 00/40 / 0000/... 0005/...

N4118.4/E0206.4 091 270 000000 LECB
BCN 116.70 019 DCT 091 425 425 00/02 00/43 / 0000/... 0005/...

N4030.0/E0223.5 164 270 000000 LECB
TOLSO 050 DCT 164 425 425 00/07 00/50 / 0000/... 0005/...

N4012.1/E0229.7 165 DSC 000000 LECB
LISAS 018 TOLS1P 165 425 425 00/02 00/53 / 0000/... 0005/...

N4005.6/E0244.3 119 DSC 000000 LECB
D300T 013 TOLS1P 119 387 387 00/01 00/55 / 0000/... 0005/...

N3955.6/E0306.8 120 DSC 000000 LECB
POS 116.40 020 TOLS1P 120 376 376 00/03 00/58 / 0000/... 0005/...

N3933.1/E0244.3 217 DSC 000000 LECB
LEPA 028 TOLS1P 217 289 289 00/05 01/04 / 0000/... 0005/..

_________________
Vaughan

If you take your config entry and modify it to use the MD82 prf file, it works fine. Consequently I suspect a fault with the MD80.prf file..

DJ

DJ,

Thanks for the follow up.

I will go ahead and use MD82 as you suggested.

_________________
Vaughan