Fsbuild-2 Flight Planner • View topic

View unanswered posts | View active topics

Board index » Fsbuild 2 Flight Planning » Fsbuild 2 Support

All times are UTC

Burn table

Moderator: ErnieAlston

Page 1 of 1

[ 11 posts ]

Previous topic | Next topic

Author

Message

reddog

Post subject: Burn table

Posted: Wed Jun 22, 2005 1:31 am

Joined: Wed Jun 22, 2005 1:29 am
Posts: 4

_________________
Thanks,
Steve

Top

reddog

Post subject:

Posted: Sun Jun 26, 2005 5:58 pm

Joined: Wed Jun 22, 2005 1:29 am
Posts: 4

_________________
Thanks,
Steve

Top

reddog

Post subject:

Posted: Sun Jul 10, 2005 2:24 am

Joined: Wed Jun 22, 2005 1:29 am
Posts: 4

_________________
Thanks,
Steve

Top

ErnieAlston

Post subject:

Posted: Sun Jul 17, 2005 2:50 pm

Joined: Thu May 19, 2005 3:45 pm
Posts: 3903
Location: NJ, USA

Top

reddog

Post subject:

Posted: Sun Jul 17, 2005 10:32 pm

Joined: Wed Jun 22, 2005 1:29 am
Posts: 4

_________________
Thanks,
Steve

Top

boris

Post subject:

Posted: Fri Jul 06, 2007 7:18 pm

Joined: Sun Apr 01, 2007 1:02 pm
Posts: 2
Location: Germany

Top

Kensei

Post subject: Re: Burn table

Posted: Mon Aug 30, 2010 12:10 pm

Joined: Tue May 25, 2010 7:06 am
Posts: 8

Let's dust off this old topic and bring new life to it shall we?

I too have the same incomplete information after creating a burn table, jus tlike Boris.

I have FSBuild 2.3 and use it, next to TOPCAT, to get more accurate information about triptimes, step profiles, fuelflow and the amount of fuel needed.
TOPCAT is alway on the low side, but that's understandable since it's mainly a take-off and landing calculationtool. However, FSBuild (connected to my ASE) will give a better estimate.

Now...after I created the template like stated here, I also get a fairly empty burn table, the same as Boris did.

How do I solve this?

Top

ErnieAlston

Post subject: Re: Burn table

Posted: Tue Aug 31, 2010 2:10 am

Joined: Thu May 19, 2005 3:45 pm
Posts: 3903
Location: NJ, USA

Top

Kensei

Post subject: Re: Burn table

Posted: Tue Aug 31, 2010 5:30 am

Joined: Tue May 25, 2010 7:06 am
Posts: 8

Top

ErnieAlston

Post subject: Re: Burn table

Posted: Tue Aug 31, 2010 8:19 pm

Joined: Thu May 19, 2005 3:45 pm
Posts: 3903
Location: NJ, USA

What Aircraft did you select ?

Regards.
Ernie.

Top

Kensei

Post subject: Re: Burn table

Posted: Tue Aug 31, 2010 8:29 pm

Joined: Tue May 25, 2010 7:06 am
Posts: 8

boeing 737-800 i selected

EDIT: I posted my answer yesterday via my phone so sorry if it sounded a bit harsh

Like I said: I select the Boeing 737-800, I enter any FP but I keep getting the empty burntable as a result...just like Boris did.
With a copy&paste of your code I can't go wrong, so...what else might be wrong here?

I also tried the B737-200 just like in the example in this topic, but to no avail.

Regards

Eric

Top

Page 1 of 1

[ 11 posts ]

Board index » Fsbuild 2 Flight Planning » Fsbuild 2 Support

All times are UTC

Who is online

Users browsing this forum: No registered users and 1 guest

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum